A Better Viewing Position For The Back Seat
Give rear passengers a dedicated place for their phone or tablet without requiring them to hold the device throughout the drive.
The telescopic arm extends from the front-seat headrest and can be repositioned to bring the screen into a more comfortable viewing area. The rotating device mount supports both portrait and landscape viewing, making it practical for videos, reading, games, navigation viewing, or general passenger entertainment.
Its foldable articulated design also lets you move the holder closer to the seat when the extended position is not needed.
Check Your Headrest & Device Before Ordering
This holder mounts to two exposed front-seat headrest posts. It is not designed for fixed or fully integrated headrests without accessible support posts.
Before ordering, confirm that your seat has two exposed posts with enough accessible clearance for the mounting hooks.
The device cradle adjusts from approximately:
13.5 to 26 cm / 5.3 to 10.2 in wide
For the most reliable fit, measure the actual width of your phone or tablet at the point where the holder will grip it rather than relying only on advertised screen size.
Works With
- Vehicle seats with two exposed headrest posts
- Phones and tablets within the verified holder-width range
- Devices used in portrait or landscape orientation
- Rear-seat passenger viewing
Does Not Work With
- Fixed or fully integrated headrests
- Seats without two accessible headrest posts
- Devices outside the verified cradle-width range
- Vehicles where the mounting area is obstructed
Important Fitment Note
Supplier fitment graphics show conflicting headrest-post spacing measurements. Because those figures cannot be reliably reconciled, a universal headrest-post spacing range should not be claimed.
Customers should confirm that their vehicle has an accessible dual-post headrest configuration before ordering.
Who Is This Product For?
This is a good fit for drivers who regularly carry passengers and want an adjustable phone or tablet mounting position behind the front seat.
Who Is This Product NOT For?
This is not suitable for customers with integrated headrests, unusual seat structures, or devices outside the verified holder-width range.
Position The Screen Where It Works Best
The articulated support arm is designed to give rear passengers more control over where the screen sits.
The arm can extend outward, pivot through its joints, and fold closer toward the front seat when required. The device cradle connects through an adjustable ball-joint assembly for additional viewing-angle control.
The mount also supports 360° device rotation, allowing easy switching between portrait and landscape orientation.
Visible supplier measurements show an adjustable arm length of approximately:
27 to 36 cm / 10.62 to 14.17 in
This flexibility makes it easier to position the device for different passengers and seating positions without permanently altering the vehicle interior.
Designed For Everyday Passenger Use
The holder uses a multi-point mechanical support design rather than adhesive mounting.
Padded contact areas help separate the device and headrest posts from the harder structural surfaces of the mount, while the adjustable cradle keeps compatible devices supported from both sides.
The low-profile black construction is designed to blend naturally into a modern vehicle interior rather than dominate it.
For longer journeys, passengers can keep the device positioned in front of them instead of continuously holding it by hand.
Simple Headrest Installation
Installation does not require drilling or permanent adhesive.
First connect the device cradle to the support arm using the visible ball-joint locking mechanism. Then position the mounting ends around the two exposed headrest posts and secure the holder according to the adjustment mechanism.
Once installed, extend and angle the arm as needed, place the compatible device into the cradle, and adjust the viewing orientation.
Installation Expectations
- Minor product assembly is required
- Two exposed headrest posts are required
- No drilling is shown
- No adhesive mounting is shown
- Device position should be adjusted before driving
- Confirm that the holder and device do not interfere with seat movement or normal vehicle operation
Built For Road Trips & Daily Passenger Convenience
This type of holder is particularly useful when rear-seat passengers spend extended time in the vehicle.
Verified customer feedback repeatedly mentions convenience, in-car usefulness, and longer-distance travel. The practical benefit is simple: passengers have a stable location for their screen without needing to continuously hold it.
When the screen is not required, the articulated arm can be repositioned or folded closer to the seat to keep the setup more compact.
Practical Construction With Easy Maintenance
The factual supplier description identifies the construction as alloy + ABS, combining a structural support frame with molded components.
The holder includes padded contact surfaces at key device and mounting points, and its smooth exterior can be wiped with a soft cloth to remove dust and fingerprints.
The product is available in:
- Black
- Black with red accent detailing
Customer feedback is generally positive about convenience and usability, although several reviews mention receiving units with cosmetic scratches or dents. Product imagery and packaging should therefore accurately represent the finish, and fulfillment quality control should prioritize cosmetic inspection before shipment.